ELIAS GmbH
Produktdokumentationen

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
~~NOTOC~~

<WRAP noprint>

> Manual <html><b><i><font color="#E12C24">mdm - </font></i> TOOL</b></html> > Input Devices

</WRAP>

====== Steinwald ======

----

The additional module for Steinwald interface boxes is not included in the basic version of <html><b><i><font color="#E12C24">mdm - </font></i> TOOL</b></html>.

<WRAP noprint>
<WRAP group>
<WRAP column 45%>
//**__Inhalt__**//

 • [[en:mdm:inputdevices:steinwald#Configuration of a Steinwald Interface Box]]\\ 
 • [[en:mdm:inputdevices:steinwald#Configuration of a Steinwald Measurement Device]]

\\ 

</WRAP>
</WRAP>
</WRAP>

===== Configuration of a Steinwald Interface Box =====

The following describes how to configure a Steinwald interface box as an input device.

{{:en:mdm:inputdevices:steinwald_eng_a1.png?500|}}

To configure the interface box select it with a single mouse click from the list.

{{:en:mdm:inputdevices:steinwald_eng_a2.png?500|}}

Click the **Configure** button below the list to open the configuration window. Alternatively you can open the context menu via a right mouse click and select the **Configure** menu entry.

{{:en:mdm:inputdevices:steinwald_eng_a3.png?500|}}

In the Configuration menu you can activate or deactivate the interface box by clicking the **Enabled ** check box.

The **COM port name** drop down menu shows all active COM ports. Select the port that the interface box should connect to. If the listed COM ports are not up to date, click the **Refresh** button to update the list.

In the **Baud rate** drop down menu you select the baud rate of the box.

Click **Apply** to accept the settings you have made. Click **OK** to save the settings and close the Settings window. Clicking **Cancel** closes the window without saving any changes. 

{{:en:mdm:inputdevices:steinwald_eng_a4.png?500|}}

<WRAP pagebreak></WRAP>

===== Configuration of a Steinwald Measurement Device =====

This section describes how to configure a measurement device of a Steinwald interface box.

{{:en:mdm:inputdevices:steinwald_eng_b1.png?500|}}

To configure the measurement device select it with a single mouse click from the list.

{{:en:mdm:inputdevices:steinwald_eng_b2.png?500|}}

Click the **Configure** button below the list of devices to open the configuration window. You can also right mouse click to open the context menu and click on **Configure**.

{{:en:mdm:inputdevices:steinwald_eng_b3.png?500|}}

In the configuration menu you can activate or deactivate the measurement device by selecting or deselecting the **Enable** check box.

You can enter a name for the devicein the **Name** field. This is then displayed in the list. This makes identification easier if there are more than one device in the list. 

The device's **Serial number** and **Type** are also displayed. These settings cannot be changed.

{{:en:mdm:inputdevices:steinwald_eng_b4.png?500|}}

In the **Feedback** menu select the output device from which you expect acknowledgement of receipt for measurement data. If you select the **Green LED** from the list, this LED on the transmitter will light up when a measurement value has been processed. Selecting **Virtual COM Port** or **Virtual Keyboard** from the list results in this device taking on the acknowledgement of receipt and the corresponding LEDs light up.

Click **Apply** to adopt the settings you have chosen. Clicking **OK** saves the data and closes the Settings window. Clicking **Cancel** closes the window without saving any changes. 

<WRAP noprint>

----

<WRAP group>
<WRAP col2>

<WRAP rightalign>
**Back to**\\ 
Input Devices > [[en:mdm:inputdevices:mux|MUX-Protokoll]]
</WRAP>

**Continue with**\\ 
Input Devices > [[en:mdm:inputdevices:sylvac|Sylvac Bluetooth]]

</WRAP>
</WRAP>

</WRAP>
ELIAS GmbHProduktdokumentationen

User Tools

Site Tools

Page Tools

ELIAS GmbH
Produktdokumentationen
