This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
en:mdm:inputdevices:steinwald [2016/01/25 10:41] sh [Configuration of a measurement device] |
en:mdm:inputdevices:steinwald [2016/02/15 10:18] sh |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ===== Steinwald Input ===== | + | ====== Steinwald ====== |
- | The additional module is not included in the basic version of the MDM-Tool. | + | The additional module for Steinwald interface boxes is not included in the basic version of MDM-Tool. |
- | ==== Configuration of a Steinwald-Interface-Box ==== | + | ===== Configuration of a Steinwald Interface Box ===== |
- | The following describes how to configure a Steinwald Interface Box as an input device. | + | The following describes how to configure a Steinwald interface box as an input device. |
{{:en:mdm:inputdevices:steinwald_eng_a1.png?500|}} | {{:en:mdm:inputdevices:steinwald_eng_a1.png?500|}} | ||
Line 24: | Line 24: | ||
Click **Apply** to accept the settings you have made. Click **OK** to save the settings and close the Settings window. Clicking **Cancel** closes the window without saving any changes. | Click **Apply** to accept the settings you have made. Click **OK** to save the settings and close the Settings window. Clicking **Cancel** closes the window without saving any changes. | ||
- | |||
- | After accepting your configurations, a corresponding number of measurement device channels is added to the list of input devices. | ||
- | |||
Line 35: | Line 32: | ||
<WRAP pagebreak></WRAP> | <WRAP pagebreak></WRAP> | ||
- | ==== Configuration of a measurement device ==== | + | ===== Configuration of a Steinwald measurement device ===== |
- | This section describes how to configure a measurement device channel of a Steinwald interface box. | + | This section describes how to configure a measurement device of a Steinwald interface box. |
{{:en:mdm:inputdevices:steinwald_eng_b1.png?500|}} | {{:en:mdm:inputdevices:steinwald_eng_b1.png?500|}} | ||
- | Click on the receiver you want to configure from the list. | + | To configure the measurement device select it with a single mouse click from the list. |
{{:en:mdm:inputdevices:steinwald_eng_b2.png?500|}} | {{:en:mdm:inputdevices:steinwald_eng_b2.png?500|}} | ||
- | Click the Configure button below the list of devices to open the configuration window. You can also right mouse click to open the context menu and click on the Configure. | + | Click the **Configure** button below the list of devices to open the configuration window. You can also right mouse click to open the context menu and click on **Configure**. |
{{:en:mdm:inputdevices:steinwald_eng_b3.png?500|}} | {{:en:mdm:inputdevices:steinwald_eng_b3.png?500|}} | ||
- | In the Configuration menu you can activate or deactivate the measurement device by selecting or deselecting the **Activate** check box. | + | In the configuration menu you can activate or deactivate the measurement device by selecting or deselecting the **Enable** check box. |
- | You can enter a name for the transmitter in the **Name** field. This is then displayed in the list. This makes identification easier if there are more than one device in the list. | + | You can enter a name for the devicein the **Name** field. This is then displayed in the list. This makes identification easier if there are more than one device in the list. |
- | The serial number and type of transmitter is also displayed. These settings cannot be changed. | + | The device's **Serial number** and **Type** are also displayed. These settings cannot be changed. |
{{:en:mdm:inputdevices:steinwald_eng_b4.png?500|}} | {{:en:mdm:inputdevices:steinwald_eng_b4.png?500|}} | ||
In the **Feedback** menu select the output device from which you expect acknowledgement of receipt for measurement data. If you select the **Green LED** from the list, this LED on the transmitter will light up when a measurement value has been processed. Selecting **Virtual COM Port** or **Virtual Keyboard** from the list results in this device taking on the acknowledgement of receipt and the corresponding LEDs light up. | In the **Feedback** menu select the output device from which you expect acknowledgement of receipt for measurement data. If you select the **Green LED** from the list, this LED on the transmitter will light up when a measurement value has been processed. Selecting **Virtual COM Port** or **Virtual Keyboard** from the list results in this device taking on the acknowledgement of receipt and the corresponding LEDs light up. | ||
+ | |||
+ | Click **Apply** to adopt the settings you have chosen. Clicking **OK** saves the data and closes the Settings window. Clicking **Cancel** closes the window without saving any changes. | ||