Differences

This shows you the differences between two versions of the page.

--- en:mdm:inputdevices:steinwald [2016/01/25 10:14]
sh
+++ en:mdm:inputdevices:steinwald [2018/03/02 13:13] (current)
me
@@ Line 1: / Line 1: @@
-===== Steinwald Input =====
+~~NOTOC~~
-The additional module is not included in the basic version of the MDM-Tool.
+<WRAP noprint>
-==== Configuration of a Steinwald-Interface-Box ====
+> Manual #@MDM_HTML@# > Input Devices
-This chapter describes how to configure a Steinwald Interface Box as an input device.
+</WRAP>
+====== Steinwald ======
+----
+The additional module for Steinwald interface boxes is not included in the basic version of #@MDM_HTML@#.
+<WRAP noprint>
+<WRAP group>
+<WRAP column 45%>
+//**__Inhalt__**//
+ • [[en:mdm:inputdevices:steinwald#Configuration of a Steinwald Interface Box]]\\
+ • [[en:mdm:inputdevices:steinwald#Configuration of a Steinwald Measurement Device]]
+\\
+</WRAP>
+</WRAP>
+</WRAP>
+===== Configuration of a Steinwald Interface Box =====
+The following describes how to configure a Steinwald interface box as an input device.
 {{:en:mdm:inputdevices:steinwald_eng_a1.png?500|}}
-To configure the box, select it from the list with the mouse pointer.
+To configure the interface box select it with a single mouse click from the list.
 {{:en:mdm:inputdevices:steinwald_eng_a2.png?500|}}
-Click the **Configure** button below the list to open the configuration menu. Alternatively you can open the menu by selecting **Configure** in the context menu.
+Click the **Configure** button below the list to open the configuration window. Alternatively you can open the context menu via a right mouse click and select the **Configure** menu entry.
 {{:en:mdm:inputdevices:steinwald_eng_a3.png?500|}}
-In the Configuration menu you can activate or deactivate the interface box by selecting or deselecting the **Activate** - check box.
+In the Configuration menu you can activate or deactivate the interface box by clicking the **Enabled ** check box.
 The **COM port name** drop down menu shows all active COM ports. Select the port that the interface box should connect to. If the listed COM ports are not up to date, click the **Refresh** button to update the list.
@@ Line 23: / Line 47: @@
 In the **Baud rate** drop down menu you select the baud rate of the box.
-When you confirm your configurations by clicking the **OK** or the **Apply** button, a corresponding number of measurement device channels is added to the list of input devices.
+Click **Apply** to accept the settings you have made. Click **OK** to save the settings and close the Settings window. Clicking **Cancel** closes the window without saving any changes.
 {{:en:mdm:inputdevices:steinwald_eng_a4.png?500|}}
-\\
 <WRAP pagebreak></WRAP>
-==== Configuration of a measurement device ====
+===== Configuration of a Steinwald Measurement Device =====
+This section describes how to configure a measurement device of a Steinwald interface box.
 {{:en:mdm:inputdevices:steinwald_eng_b1.png?500|}}
+To configure the measurement device select it with a single mouse click from the list.
 {{:en:mdm:inputdevices:steinwald_eng_b2.png?500|}}
+Click the **Configure** button below the list of devices to open the configuration window. You can also right mouse click to open the context menu and click on **Configure**.
 {{:en:mdm:inputdevices:steinwald_eng_b3.png?500|}}
+In the configuration menu you can activate or deactivate the measurement device by selecting or deselecting the **Enable** check box.
+You can enter a name for the devicein the **Name** field. This is then displayed in the list. This makes identification easier if there are more than one device in the list.
+The device's **Serial number** and **Type** are also displayed. These settings cannot be changed.
 {{:en:mdm:inputdevices:steinwald_eng_b4.png?500|}}
+In the **Feedback** menu select the output device from which you expect acknowledgement of receipt for measurement data. If you select the **Green LED** from the list, this LED on the transmitter will light up when a measurement value has been processed. Selecting **Virtual COM Port** or **Virtual Keyboard** from the list results in this device taking on the acknowledgement of receipt and the corresponding LEDs light up.
+Click **Apply** to adopt the settings you have chosen. Clicking **OK** saves the data and closes the Settings window. Clicking **Cancel** closes the window without saving any changes.
+<WRAP noprint>
+----
+<WRAP group>
+<WRAP col2>
+<WRAP rightalign>
+**Back to**\\
+Input Devices > [[en:mdm:inputdevices:mux|MUX-Protokoll]]
+</WRAP>
+**Continue with**\\
+Input Devices > [[en:mdm:inputdevices:sylvac|Sylvac Bluetooth]]
+</WRAP>
+</WRAP>
+</WRAP>

ELIAS GmbHProduktdokumentationen

User Tools

Site Tools

Differences

Page Tools

ELIAS GmbH
Produktdokumentationen