This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
en:mdm:plugins:infra-dat [2016/01/15 14:38] je |
— (current) | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ===== infra-DAT ===== | ||
- | |||
- | ==== Connecting a infra-DAT transmitter ==== | ||
- | |||
- | The following section describes how to connect an infra-DAT transmitter with your PC. To add a transmitter to the **Input devices** list, connect the transmitter via the digital interface to the measuring device and switch the latter on. | ||
- | |||
- | {{:en:mdm:connect_infra-dat-1_2.png?500|}} | ||
- | |||
- | |||
- | Double click the **+ Add new device** entry field in the **infra-DAT** list to open the devices list. All transmitters that are recognized are listed here. Devices that are turned off are not recognized. Briefly press the on/off button on the transmitter to turn it on and the transmitter will appear in the list. | ||
- | |||
- | |||
- | {{:en:mdm:connect_infra-dat-select-device_2.png?500|}} | ||
- | |||
- | |||
- | Click to select the transmitter you want to connect and then click **Add**. The transmitter now appears in the **Input devices** list and is automatically connected to the standard output device, the **Virtual Keyboard**. | ||
- | \\ \\ | ||
- | |||
- | <WRAP info> If the transmitter is not found, click on **Transmitter is not listed**. Follow the software instructions.</WRAP> | ||
- | |||
- | |||
- | {{:en:mdm:connect_infra-dat-device_added_2.png?500|}} | ||
- | |||
- | |||
- | Pressing the transmitter button sends the measurement data from your measuring devices to the keyboard interface. Transmitted measurement values are then displayed in the lower part of the window. As a check, compare these values with those displayed on your measuring device. | ||
- | \\ | ||
- | \\ | ||
- | The green icon next to the Transmitter name is short green during data transfer. | ||
- | \\ | ||
- | \\ | ||
- | <WRAP pagebreak></WRAP> | ||
- | ==== Configuring an infra-DAT transmitter ==== | ||
- | |||
- | This section describes how to configure an infra-DAT transmitter. | ||
- | \\ | ||
- | \\ | ||
- | To configure a transmitter select it with a single mouse click from the list. | ||
- | |||
- | |||
- | {{:en:mdm:configuration-infra-dat-transmitter-select_2.png?500|}} | ||
- | |||
- | |||
- | Click the **Configure** button below the list to open the configuration window. Alternatively you can open the context menu via a right mouse click and select the **Configure** menu entry. | ||
- | |||
- | |||
- | {{:en:mdm:configuration-infra-dat-transmitter-context_2.png?500|}} | ||
- | |||
- | |||
- | {{:en:mdm:configuration-infra-dat-transmitter-window_2.png?500|}} | ||
- | |||
- | |||
- | |||
- | You can activate or deactivate the infra-DAT transmitter by clicking the **Enabled** check box. | ||
- | |||
- | \\ | ||
- | \\ | ||
- | You can enter a name for the transmitter in the **Name** entry field. This is displayed in the devices list, making the identification of individual devices easier. | ||
- | \\ | ||
- | \\ | ||
- | Serial number and transmitter type are also displayed. This setting cannot be changed. | ||
- | |||
- | |||
- | {{:en:mdm:configuration-infra-dat-transmitter-ack_2.png?500|}} | ||
- | |||
- | Enter the output device from which you expect acknowledgment of receipt in the **Feedback** field. | ||
- | \\ | ||
- | \\ | ||
- | You can remove the device from the list by clicking on **Delete**. | ||
- | \\ | ||
- | \\ | ||
- | Click **Apply** to accept the settings you have made. Click **OK** to save the settings and close the Settings window. Clicking **Cancel** closes the window without saving any changes. | ||
- | \\ | ||
- | \\ | ||
- | <WRAP pagebreak></WRAP> | ||
- | |||
- | ==== Configuring an infra-DAT receiver ==== | ||
- | |||
- | This section describes how to configure a infra-DAT receiver. | ||
- | \\ | ||
- | \\ | ||
- | Click on the receiver you want to configure from the list. | ||
- | |||
- | |||
- | {{:en:mdm:configuration-infra-dat-receiver-select_2.png?500|}} | ||
- | |||
- | |||
- | Click the **Configure** button below the list of devices to open the configuration window. You can also right mouse click to open the context menu and click on the **Configure**. | ||
- | |||
- | |||
- | {{:en:mdm:configuration-infra-dat-receiver-context_2.png?500|}} | ||
- | |||
- | |||
- | {{:en:mdm:configuration-infra-dat-receiver-window_2.png?500|}} | ||
- | \\ | ||
- | \\ | ||
- | You use the **Enabled** check box in the configuration window to activate or deactivate the infra-DAT receiver. | ||
- | \\ | ||
- | \\ | ||
- | The receiver's serial number of the receiver is also displayed. This setting cannot be changed. | ||
- | \\ | ||
- | \\ | ||
- | You can change the frequency channel the receiver uses in the **Channel** selection field. The standard setting is delivered channel 54. | ||
- | |||
- | <WRAP important>Caution! Changing the frequency channel breaks contact with the receiver as it has not been set to work with the new frequency channel.</WRAP> | ||
- | |||
- | To accept the changes click **Apply**, and click **OK** to save the data and close the configuration settings window. Clicking on **Cancel** closes the settings window without saving any changes. | ||
- | \\ | ||
- | \\ | ||
- | <WRAP pagebreak></WRAP> | ||