ELIAS GmbH
Produktdokumentationen

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
~~NOTOC~~

<WRAP noprint>

> Administrator’s Guide #@IC_HTML@# > Configuration and Import

</WRAP>

<WRAP group>
<WRAP column 90%>
====== "Settings" Parameter file ======

----
</WRAP>
<WRAP column 5%>
{{ :en:infra-convert:dev:icon_dev_einstellungen.png?nolink&50|}}
</WRAP>
</WRAP>

All the basic settings (“Settings” Menu in the program) are stored in the parameter file "settings.json". A superior description of how to use the parameter file is described under "Introduction > [[en:infra-convert:dev:intro_v2|Overview (program version 2)]]" respectively "Introduction > [[en:infra-convert:dev:intro|Overview (program version 1)]]".

During installation, the “settings” parameter file is saved at the following location:

<WRAP group>
<WRAP indent>
<WRAP column 72%>
<code>%ProgramData%\ELIAS GmbH\infra-convert\settings.json</code>
</WRAP>
</WRAP> </WRAP>

If another parameter file is to be loaded when starting the program, this can be specified in the startup parameter file (see "Configuration and Import > [[en:infra-convert:dev:parameter#Settings]]").

> **Important** If the parameter file is faulty, this can lead to a program crash. Please only change designated parameters ({{:en:infra-convert:icon_hinweis_bearbeiten_erlaubt.png?nolink&15}}). Please do not delete parameters marked with {{{:en:infra-convert:icon_hinweis_stop.png?nolink&15}} and do not change values assigned to them.

<WRAP noprint>
<WRAP group>
<WRAP column 25%>
//**__Content__**//

 • [[en:infra-convert:dev:settings#Administrator tools]]\\ 
 • [[en:infra-convert:dev:settings#Set-up]]\\ 
 • [[en:infra-convert:dev:settings#List of the settings]]\\ 
 • [[en:infra-convert:dev:settings#Installation/Deinstallation]]

\\ 

</WRAP>
</WRAP>

</WRAP>

===== Administrator tools =====

<WRAP group>
<WRAP column 25%>

**Export file with default values**

</WRAP>

<WRAP column 65%>

You can export a complete "settings.json" with default settings from the #@IC_HTML@# user interface in administrator mode. (Available from program version 2.2.3)\\ **Siehe** User Manual > Settings > Setup > Administration > [[en:infra-convert:user:config:export#export_configuration_files_group|“Export configuration files” group]].

</WRAP>
</WRAP>

\\ 


===== Set-up =====

<WRAP group>
<WRAP column 40%>

The settings are written in fields with the structure shown here.

</WRAP>
<WRAP column 55%>

**From program version 2.0.0.0 applies:**

<code javascript>
"Culture": {
  "Value": "de-DE",
},
</code>

|< 100% 20% 10% 50% 10% >|
^  Parameter  ^  Type  ^  Value/Content  ^  ^
^ Value | – | Value of the setting |  {{:en:infra-convert:icon_hinweis_bearbeiten_erlaubt.png?nolink&20}}  |

\\ 

**For older program versions applies:**

<code javascript>
"Culture": {
  "Name": "Culture",
  "Value": "de-DE",
  "DefaultValue": "de-DE",
  "ValueType": "System.Globalization.CultureInfo, mscorlib, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089",
  "IsTempSetting": false
},
</code>

|< 100% 20% 10% 50% 10% >|
^  Parameter  ^  Type  ^  Value/Content  ^  ^
^ Name | String | Name of the setting; always includes the field name. |  {{:en:infra-convert:icon_hinweis_stop.png?nolink&20}}  |
^ Value | – | Value of the setting |  {{:en:infra-convert:icon_hinweis_bearbeiten_erlaubt.png?nolink&20}}  |
^ DefaultValue | – | Factory-set value |  {{:en:infra-convert:icon_hinweis_stop.png?nolink&20}}  |
^ ValueType | String | Internal parameters, including data type and program library to be used. |  {{:en:infra-convert:icon_hinweis_stop.png?nolink&20}}  |
^ IsTempSetting | Boolean | Internal parameter. |  {{:en:infra-convert:icon_hinweis_stop.png?nolink&20}}  |

</WRAP>
</WRAP>

\\ 

==== List of the settings ====

The following table lists the values for the setting parameters and links to detailed descriptions.

<WRAP group>
<WRAP column 3%>
{{:en:infra-convert:icon_hinweis_bearbeiten_erlaubt.png?nolink&25}}
</WRAP>
<WRAP column 92%>
**“Settings > General” menu**
</WRAP>
</WRAP>

|< 100% 20% 40% 40% >|
^  Name  ^  Value  ^  Link  ^
^ MonochromeModeEnabled | Monochrome moen:\\ **true** on\\ **false** off | User manual > Settings > Settings > General > [[en:infra-convert:user:config:general#“Display” group]] |
^ CadViewBackgroundColor | Background colour in HTML colour code | User manual > Settings > Settings > General > [[en:infra-convert:user:config:general#“Display” group]] |
^ MultisamplingLevel | Improve image quality by antialiasing\\ **16** Level: 16\\ **8** Level: 8\\ **4** Level: 4\\ **2** Level: 2\\ **0** Off\\ \\ **Note** Available from program version 1.5.1.1 | User manual > Settings > Settings > General > [[en:infra-convert:user:config:general#“Display” group]] |
^ UseMipmappingForPaletteImages | Improve display of raster graphics through Mipmapping:\\ **true** on\\ **false** off\\ \\ **Note** Available from program version 1.5.1.7 | User manual > Settings > Settings > General > [[en:infra-convert:user:config:general#“Display” group]] |
^ Culture | Language:\\ **de-DE** German\\ **en-EN** English\\ **fr-FR** French\\ **it-IT** Italian\\ **es-ES** Spanish\\ **ru-RU** Russian | User manual > Settings > Settings > General > [[en:infra-convert:user:config:general#“Language” group|“Language” Group]] > Table |
^ DefaultProjectFolder | File path to default project folder | User manual > Settings > Settings > General > [[en:infra-convert:user:config:general#“Project” group]] |
^ AllowDuplicateInspectionPlanVersions | Allow duplicate titles for each quality control plan and version:\\ **true** on\\ **false** off | User manual > Settings > Settings > General > [[en:infra-convert:user:config:general#“Project” group]] |
^ AllowTestPlanVersionsNumberChange | The quality control plan version can be changed by the user:\\ **true** on\\ **false** off | User manual > Settings > Settings > General > [[en:infra-convert:user:config:general#“Project” group]] |
^ AllowCompareWithNewerVersions | Allow drawings to be compared with newer quality control plan versions or those with the same name:\\ **true** on\\ **false** off | User manual > Settings > Settings > General > [[en:infra-convert:user:config:general#“Project” group]] |
^ AutosaveEnabled | Save project automatically:\\ **true** on\\ **false** off\\ \\ **Note** Available from program version 1.3.1.5. | User manual > Settings > Settings > General > [[en:infra-convert:user:config:general#“Project” group]] |
^ AutosaveInterval | Interval for automatic saving of the project in minutes (format: integer)\\ \\ **Note** Available from program version 1.3.1.5. | User manual > Settings > Settings > General > [[en:infra-convert:user:config:general#“Project” group]] |
^ LicenseServerUrl | Network address of the licence service (host and port as URL) | Settings > Settings > General > [[en:infra-convert:user:config:general#“License server” group]] |
^ ActiveUserSessionsVisible | Display users in license dialog\\ \\ **Note** Available from program version 2.4.11. | Settings > Settings > General > [[en:infra-convert:user:config:general#“License server” group]] |

\\ 

<WRAP group>
<WRAP column 3%>
{{:en:infra-convert:icon_hinweis_bearbeiten_erlaubt.png?nolink&25}}
</WRAP>
<WRAP column 92%>
**“Settings > Characteristics” menu**
</WRAP>
</WRAP>

|< 100% 20% 40% 40% >|
^  Name  ^  Value  ^  Link  ^
^ AllowMultipleCharacteristicTags | Characteristic may have multiple tags:\\ **true** Apply label\\ **false** Reset label | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#"General characteristic settings" group]] |
^ TitlePattern | Format title of variable characteristics | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#"Format characteristic title" group]] |
^ TitlePatternAttributive | Format title of attributive characteristics | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#"Format characteristic title" group]] |
^ SignificantDigitsDefault | Converted results (Degree, Minute, Second to decimal) and calculations (Tolerance value as a fraction of the nominal value) are rounded to … significant digits\\ \\ **Note** Available from program version 1.3.9.9. | More > Terms > [[en:infra-convert:user:terms#numerical_precision|Numerical precision]]\\ Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#numerical_precision_group|“Numerical precision” group]] |
^ SignificantDigitsOne | Converted results (Degree, Minute, Second to decimal) and calculations (Tolerance value as a fraction of the nominal value) are rounded to … significant digits if the first relevant digit is a '1'..\\ \\ **Note** Available from program version 1.3.9.9. | More > Terms > [[en:infra-convert:user:terms#numerical_precision|Numerical precision]]\\ Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#numerical_precision_group|“Numerical precision” group]] |
^ CharacteristicCreateWithMinimumDecimalPlaces | Create numerical values with at least n decimal places\\ **0** Settings > Settings > Characteristic > [[en:infra-convert:user:config:features#number_format_group|“Number format” group]] |
^ CharacteristicAttributiveCharacteristic | Attributive characteristics are\\ **SingleSelection** ignored in multiselection mode\\ **Always** always created\\ **Never** always ignored | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#“Attributive characteristic” group]] |
^ CharacteristicInfotextCharacteristic | Auxiliary dimensions are\\ **SingleSelection** ignored in multiselection mode\\ **Always** always created\\ **Never** always ignored | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#“Word specifications” group]] |
^ CharacteristicDimensionWithoutTolerance | Characteristics from dimensions without tolerance entry directly at nominal value are\\ **SingleSelection** ignored in multiselection mode\\ **Always** always created\\ **Never** always ignored | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#“Measurements without tolerance entry at nominal dimension” group]] |
^ CharacteristicMinMax | Limit values in one direction (min./max.):\\ \\ The following applies from program version 1.2.0.26 upwards:\\ **WithoutTolerance** Create limit value as nominal value\\ **WithOneTolerance** Create nominal value with upper or lower tolerance\\ **WithBothTolerances** Create nominal value and limit value as tolerances\\ **OnlyOneTolerance** Create limit value only\\ **Never** Ignore supplementary 'min./max.' information\\ \\ The following applies up to the above program version:\\ **WithoutTolerance** Create without tolerances\\ **WithOneTolerance** Create with upper or lower tolerance\\ **WithBothTolerances** Create with nominal value and tolerance\\ **OnlyOneTolerance** Create with one tolerance and nominal value of zero\\ **Never** Always ignore | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#“Limit values in one direction (min., max.)” group]] |
^ CharacteristicMinMaxNullTolerance | Limit value in one direction (min./max.): zero values are not applied in characteristic:\\ **true** Yes\\ **false** No | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#“Limit values in one direction (min., max.)” group]] |
^ CharacteristicDimensionNominalValueNull | Characteristics with nominal value of zero are\\ **SingleSelection** ignored in multiselection mode\\ **Always** always created\\ **Never** always ignored | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#“Characteristics with nominal dimensions zero” group]] |
^ CharacteristicAngleDimensions | Create angle dimensions as\\ **true** variable characteristic\\ **false** attributive characteristic | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#“Angular measurements” group]] |
^ MultiCharacteristicSplitt | Create individual characteristics from dimensions, indicating repetitions:\\ **true** Yes\\ **false** No | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#“Dimensions with details of repetitions” group]] |
^ CharacteristicAuxiliaryDimension | Auxiliary dimensions are\\ **SingleSelection** ignored in multiselection mode\\ **Always** always created\\ **Never** always ignored | User manual > Settings > Settings > [[en:infra-convert:user:config:features#“Auxiliary dimensions” group]] |
^ CharacteristicAuxiliaryDimensionUseTolerance | Auxiliary dimensions: use tolerances:\\ **true** Yes\\ **false** No | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#“Auxiliary dimensions” group]] |
^ CharacteristicTheoreticDimension | Theoretically precise measurements are\\ **SingleSelection** ignored in multiselection mode\\ **Always** always created\\ **Never** always ignored | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#“Theoretically precise measurements” group]] |
^ CharacteristicTheoreticDimensionUseTolerace | Theoretically precise measurements: use tolerances:\\ **true** Yes\\ **false** No | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#“Theoretically precise measurements” group]] |
^ CharacteristicGeometricDimensioningTolerancing | Processing the shape and positional tolerances:\\ **Nominal** Nominal value = width of the tolerance zone; Upper tol. = 0; Lower tol. = 0\\ **NominalWithLower** Nominal value = width of the tolerance zone; Upper tol. = 0; Lower tol. = (-1) x width of the tolerance zone\\ **Upper** Nominal value = 0; Upper tol. = width of the tolerance zone; Lower tol. = 0\\ **NominalWithUpper** Nominal value = width of the tolerance zone; Upper tol. = width of the tolerance zone; Lower tol. = 0 | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#“Shape and positional tolerances” group]] |
^ CharacteristictGdtNullTolerance | Shape and positional tolerances: zero values are not applied in the characteristic:\\ **true** Yes\\ **false** No | Settings > Settings > Characteristics> [[en:infra-convert:user:config:features#“Shape and positional tolerances” group]] |
^ CharacteristicRadiusEnable | Define radius as\\ **true** "Radius” class \\ **false** "Curve” class | User manual > Settings > Settings > [[en:infra-convert:user:config:features#“Radii” group]] |
^ CharacteristicUseRoundnesOrLeghtTolerance | Radius measurement: general tolerances applied:\\ **true** Table for curves and chamfers\\ **false** Table for linear measures | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#“Radii” group]] |
^ CharacteristicChamferVariable | Create chamfer as\\ **true** variable characteristic\\ **false** attributive characteristic | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#“Chamfer” group|“Chamfers” group]] |
^ CharacteristicChamferEdges | Edges with indeterminate shape: if no nominal value is defined, nominal value = 0:\\ **true** Yes\\ **false** No | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#“Edges with indeterminate shape” group|“Edges with indeterminate shape" group]] |
^ CharacteristicRoughness | Surface parameters: **Nominal** Nominal value = limit value; Upper tol. = 0; Lower tol. = 0\\ **NominalWithLower** Nominal value = limit value; Upper tol. = 0; Lower tol. = (-1) x limit value\\ **OnlyOneTolerance** Nominal value = 0; Upper tol. = nominal value; Lower tol. = 0\\ **NominalWithUpper** Nominal value = limit value; Upper tol. = limit value; Lower tol. = 0 | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#“Surface parameters” group]] |
^ CharacteristicRoughnessNullTolerance | Surface parameters: zero values are not applied in the characteristic:\\ **true** Yes\\ **false** No | User manual > Settings > Settings > Characteristics > [[en:infra-convert:user:config:features#“Surface parameters” group]] |
^ RoughnessDictionary | Simplified surface parameters: assignment of letter (**Key**) and numerical value (**Value**) | User manual > Settings > Settings > [[en:infra-convert:user:config:features#“Simplified surface specifications” group]] |

\\ 

<WRAP group>
<WRAP column 3%>
{{:en:infra-convert:icon_hinweis_bearbeiten_erlaubt.png?nolink&25}}
</WRAP>
<WRAP column 92%>
**“Settings > Stamp” menu**
</WRAP>
</WRAP>

|< 100% 20% 40% 40% >|
^  Name  ^  Value  ^  Link  ^
^ DefaultStampStartValue | Initial value\\ \\ **Info** Observe permitted range of values! | User manual > Settings > Settings > Stamp > [[en:infra-convert:user:config:stamps#“Marking” group]] |
^ DefaultStampIncrementSetting | Increment\\ \\ **Info** Observe permitted range of values! | User manual > Settings > Settings > Stamp > [[en:infra-convert:user:config:stamps#“Marking” group]] |
^ MinimumStampNumberDigits | Minimum number of digits\\ **0** Do not specify a minimum number\\ **1** to **10** Number of digits\\ \\ **Note** Available as of programme version 2.6.1 | User manual > Settings > Settings > Stamp > [[en:infra-convert:user:config:stamps#“Marking” group]] |
^ MergedCharacteristicNumber | Labelling of stamp in Drawings Comparison:\\ **NewNumber** Reset label\\ **KeepNumber** Apply existing label | User manual > Settings > Settings > Stamp > [[en:infra-convert:user:config:stamps#"Marking of the stamps during drawing comparison" group]] |
^ AutomaticTransfer | Transfer of manually inserted characteristics during drawing comparison:\\ **true** Yes\\ **false** No | User manual > Settings > Settings > Stamp > [[en:infra-convert:user:config:stamps#"“Transfer of manually inserted characteristics during drawing comparison” group]]  |

\\ 

<WRAP group>
<WRAP column 3%>
{{:en:infra-convert:icon_hinweis_bearbeiten_erlaubt.png?nolink&25}}
</WRAP>
<WRAP column 92%>
**“Settings > Import” menu**
</WRAP>
</WRAP>

|< 100% 20% 40% 40% >|
^  Name  ^  Value  ^  Link  ^
^ PdfDefaultImportSetting | Behaviour when importing multi-page PDF files:\\ **Ask** Allways ask before import\\ **ImportAllPages** Allways import all sheets\\ \\ **Note** Available from program version 1.4.0.2 | User manual > Settings > Settings > Import > [[en:infra-convert:user:config:import#pdf_drawing_files_group|“PDF drawing files” group]] |
^ MultiLayoutDefaultImportSetting | Behaviour when importing DXF and DWG files:\\ **Ask** Allways ask before import\\ **ImportModel** Always import model space only\\ **ImportPaperSpaces** Always import all sheets from paper space\\ **ImportAllLayouts** Allways import all sheets\\ \\ **Note** Available from program version 1.4.0.2 | User manual > Settings > Settings > Import > [[en:infra-convert:user:config:import#dxf_and_dwg_drawing_files_group|“DXF and DWG drawing files” group]] |
^ DefaultImportPdfAsRasterImage | Import PDF as raster graphics:\\ **true** Yes\\ **false** No\\ \\ **Note** Available from program version 1.4.2.1 | User manual > Settings > Settings > Import > [[en:infra-convert:user:config:import#pdf_drawing_files_group|“PDF drawing files” group]] |
^ DefaultImportPdfAsRasterImageDpi | Resolution or dot density of the raster graphics to be generated, specified as a numerical value\\ \\ **Note** Available from program version 1.4.2.1 | User manual > Settings > Settings > Import > [[en:infra-convert:user:config:import#pdf_drawing_files_group|“PDF drawing files” group]] |
^ DefaultImportPdfAsRasterImageColorDepth | Color depth of the raster graphics to be generated:\\ **0** Color (24 Bit)\\ **1** Color (8 Bit)\\ **2** Grayscale (24 Bit)\\ **3** Monochrome (1 Bit)\\ \\ **Note** Available from program version 1.4.2.1 | User manual > Settings > Settings > Import > [[en:infra-convert:user:config:import#pdf_drawing_files_group|“PDF drawing files” group]] |
^ SuppressFontReplacementNotification | Suppress notifications for replaced fonts:\\ **true** on\\ **false** off\\ \\ **Note** Available from program version 1.3.9.10 | User manual > Settings > Import > [[en:infra-convert:user:config:import#font_replacement_group|“Font replacement” group]] |

\\ 

<WRAP group>
<WRAP column 3%>
{{:en:infra-convert:icon_hinweis_bearbeiten_erlaubt.png?nolink&25}}
</WRAP>
<WRAP column 92%>
**“Settings > Export” menu**
</WRAP>
</WRAP>

|< 100% 20% 40% 40% >|
^  Name  ^  Value  ^  Link  ^
^ ExcelReportsPath | Path to directory of template files for export of Excel quality control reports | User manual > Settings > Export > [[en:infra-convert:user:config:export#“Excel test plan” group|“Excel quality control plan” group]] |
^ ExcelReportsDecimalSeperator | Decimal separator for nominal values and tolerances:\\ **Dot** Always use a dot.\\ **Comma** Always use a comma.\\ **Culture** Depends on the courrent systems' culture.\\ \\ **Note** No longer used as of programme version 2.5.3. | User manual > Settings > Export > [[en:infra-convert:user:config:export#“Excel test plan” group|“Excel quality control plan” group]] |
^ OpenExcelAfterExport | Open Microsoft Excel after the export process:\\ **true** Yes\\ **false** No\\ \\ **Note** Available from programme version 2.5.4. | User manual > Settings > Export > [[en:infra-convert:user:config:export#“Excel test plan” group|“Excel quality control plan” group]] |
^ UseExcelForTableExport | Use Microsoft Excel for the export process:\\ **true** Yes\\ **false** No\\ \\ **Note** Available from programme version 2.5.4. | User manual > Settings > Export > [[en:infra-convert:user:config:export#“Excel test plan” group|“Excel quality control plan” group]] |
^ CsvExportHeaderRow | Export additional title row when exporting to a CSV file:\\ **true** Yes\\ **false** No | User manual > Settings > Export > [[en:infra-convert:user:config:export#“CSV export” group|“CSV export” group]] |
^ GraphicsExportDrawing | Drawing graphics, defined by the following parameters in “Value” field:\\ \\ __Format__\\ **Jpg** File format "JPG"\\ **Png** File format "PNG"\\ **Bmp** File format "BMP"\\ **Tif** File format "TIF"\\ **Gif** File format "GIF"\\ \\ __Encoding__\\ **zero** No value assigned\\ (The parameter is not currently in use)\\ \\ __LanguageCode__\\ **zero** No value assigned\\ **de** Coding: English\\ \\ __Path__\\ Path to directory that is opened directly when saving in File Explorer\\ \\ __Prefix__\\ **zero** No value assigned\\ (The parameter is not currently in use)\\ \\ __DfdHeader__\\ **zero** No value assigned\\ (The parameter is not currently in use)\\ \\ __CsvHeader__\\ **zero** No value assigned\\ (The parameter is not currently in use)\\ \\ __ImageOptions__\\ └ __Width__\\   Width of graphic in number of pixels\\ └ __Height__\\   Height of graphic in number of pixels\\ └ __Bit__\\   **8** Colour depth: 8 -bit\\   **24** Colour depth: 24-bit\\ └ __SupersamplingFactor__\\  Quality level for supersampling:\\  **2** to **5** Steps 2 to 5\\ └ __SupersamplingAlgorithm__\\  Supersampling method:\\   **None** Do not apply supersampling\\  **Box** Average\\  **Bilinear** Linear\\  **Bicubic** Cubic\\  **Bspline** B-Spline\\  **Catmullrom** Catmull-Rom\\  **Lanczos3** Lanczos 3\\ \\ __ColorOption__\\ **WithColor** Non-transparent background\\ \\ __Mode__\\ **Drawing** Drawing graphic with stamps\\ **DrawingWithoutStamps** Drawing graphic without stamps\\ \\ __TemplatePath__\\ **zero** No value assigned\\ (The parameter is not currently in use)\\ \\ **Note** Supersampling is available from program version 2.2.6 | User manual > Settings > Export > [[en:infra-convert:user:config:export#“Drawing graphic format” group|“Drawing graphic” group]] |
^ ExportDrawingOnSave | Export drawing graphic when saving:\\ **true** Yes\\ **false** No | User manual > Settings > Export > [[en:infra-convert:user:config:export#“Drawing graphic format” group|“Drawing graphic” group]] |
^ GraphicsExportStamps | Stamp graphics, defined by the following parameters in “Value” field:\\ \\ __Format__\\ **Jpg** File format "JPG"\\ **Png** File format "PNG"\\ **Bmp** File format "BMP"\\ **Tif** File format "TIF"\\ **Gif** File format "GIF"\\ \\ __Encoding__\\ **zero** No value assigned\\ (The parameter is not currently in use)\\ \\ __LanguageCode__\\ **zero** No value assigned\\ **de** Coding: English\\ \\ __Path__\\ Path to directory that is opened directly when saving in File Explorer\\ \\ __Prefix__\\ **zero** No value assigned\\ (The parameter is not currently in use)\\ \\ __DfdHeader__\\ **zero** No value assigned\\ (The parameter is not currently in use)\\ \\ __CsvHeader__\\ **zero** No value assigned\\ (The parameter is not currently in use)\\ \\ __ImageOptions__\\ └ __Width__\\   Width of graphic in number of pixels\\ └ __Height__\\   Height of graphic in number of pixels\\ └ __Bit__\\   **8** Colour depth: 8 -bit\\   **24** Colour depth: 24-bit\\ └ __SupersamplingFactor__\\  Quality level for supersampling:\\  **2** to **5** Steps 2 to 5\\ └ __SupersamplingAlgorithm__\\  Supersampling method:\\   **None** Do not apply supersampling\\  **Box** Average\\  **Bilinear** Linear\\  **Bicubic** Cubic\\  **Bspline** B-Spline\\  **Catmullrom** Catmull-Rom\\  **Lanczos3** Lanczos 3\\ \\ __ColorOption__\\ **WithColor** Non-transparent background\\ \\ __Mode__\\ **Stamps** Drawing graphics each receive a stamp\\ \\ __TemplatePath__\\ **zero** No value assigned\\ (The parameter is not currently in use)\\ \\ **Note** Supersampling is available from program version 2.2.6 | User manual > Settings > Export > [[en:infra-convert:user:config:export#“Stamp graphic format” group|“Stamp graphics” group]] |
^ ExportStampsOnSave | Export stamp graphics when saving:\\ **true** Yes\\ **false** No | User manual > Settings > Export > [[en:infra-convert:user:config:export#“Stamp graphic format” group|“Stamp graphics” group]] |
^ StampExportFilenamePattern | Naming of stamp graphics\\ **{GUID}** With the GUID of the stamp\\ **{IPT}_{IPV}_{STAMPTXT}** Composed of inspection plan title, version and stamp text\\ \\ **Note** Available from program version 2.5.0 | User manual > Settings > Export > [[en:infra-convert:user:config:export#“Stamp graphic format” group|“Stamp graphics” group]] |


\\ 

<WRAP group>
<WRAP column 3%>
{{:en:infra-convert:icon_hinweis_bearbeiten_erlaubt.png?nolink&25}}
</WRAP>
<WRAP column 92%>
**“Project settings > Tolerance tables” menu**
</WRAP>
</WRAP>

|< 100% 20% 40% 40% >|
^  Name  ^  Value  ^  Link  ^
^ ToleranceTablePath | Path to the tolerance table directory | Administrator’s Guide > Configuration and Import > [[en:infra-convert:dev:toltab|Tolerance tables]] |
^ DefaultLengthToleranceTable | GUID of the standard tolerance table for length | User manual > Settings > Project settings > Tolerance tables > [[en:infra-convert:user:config:tolerancetables#“Length measurements” group]]\\ \\ Administrator’s Guide > Configuration and Import > Tolerance tables > [[en:infra-convert:dev:toltab#Id]] |
^ DefaultLengthToleranceTableColumn | Name of default tolerance class/row for length | User manual > Settings > Project settings > Tolerance tables > [[en:infra-convert:user:config:tolerancetables#“Length measurements” group]]\\ \\ Administrator’s Guide > Configuration and Import > Tolerance tables > [[en:infra-convert:dev:toltab#Columns]] |
^ DefaultAngleToleranceTable | GUID of default tolerance table for angle dimensions | User manual > Settings > Project settings > Tolerance tables > [[en:infra-convert:user:config:tolerancetables#“Angular measurements” group]]\\ \\ Administrator’s Guide > Configuration and Import > Tolerance tables > [[en:infra-convert:dev:toltab#Id]] |
^ DefaultAngleToleranceTableColumn | Name of default tolerance class/row for angle dimensions | User manual > Settings > Project settings > Tolerance tables > [[en:infra-convert:user:config:tolerancetables#“Angular measurements” group]]\\ \\ Administrator’s Guide > Configuration and Import > Tolerance tables > [[en:infra-convert:dev:toltab#Columns]] |
^ DefaultRoundnessToleranceTable | GUID of default tolerance table for curve radii and chamfers | User manual > Settings > Project settings > Tolerance tables > [[en:infra-convert:user:config:tolerancetables#“Radius of curvature and chamfers” group]]\\ \\ Administrator’s Guide > Configuration and Import > Tolerance tables > [[en:infra-convert:dev:toltab#Id]] |
^ DefaultRoundnessToleranceTableColumn | Name of default tolerance table for curve radii and chamfers | User manual > Settings > Project settings > Tolerance tables > [[en:infra-convert:user:config:tolerancetables#“Radius of curvature and chamfers” group]]\\ \\ Administrator’s Guide > Configuration and Import > Tolerance tables > [[en:infra-convert:dev:toltab#Columns]] |

\\ 

<WRAP group>
<WRAP column 3%>
{{:en:infra-convert:icon_hinweis_bearbeiten_erlaubt.png?nolink&25}}
</WRAP>
<WRAP column 92%>
**Settings with no control elements in user interfaces**
</WRAP>
</WRAP>

|< 100% 20% 40% 40% >|
^  Name  ^  Value  ^  Link  ^
^ StampPrefix | Value for "Prefix" entered in the Stamp-with-dialog | User Manual > Functions > Characteristics > Automatic stamping > [[en:infra-convert:user:functions:ballooning#workflow|Workflow]]\\ \\ User Manual > Functions > Characteristics > Manual stamping > [[en:infra-convert:user:functions:ballooning_man#workflow|Workflow]] |
^ StampPostfix | Value for "Suffix" entered in the Stamp-with-dialog | User Manual > Functions > Characteristics > Automatic stamping > [[en:infra-convert:user:functions:ballooning#workflow|Workflow]]\\ \\ User Manual > Functions > Characteristics > Manual stamping > [[en:infra-convert:user:functions:ballooning_man#workflow|Workflow]] |
^ ZoomFactor | Factor for the zoom with the mouse wheel. | User manual > Functions > View > [[en:infra-convert:user:interface:viewtools|Viewing tools]] |
^ ZoomToolFactor | Factor for the zoom with a zoom-in/zoom-out tool. | User manual > Functions > View > [[en:infra-convert:user:interface:viewtools|Viewing tools]] |
^ DisplayViewTools | Visibility of the view tools in the main toolbar:\\ **true** folded out (all visible)\\ **false** collapsed (only **Show whole drawing sheet** visible)\\ \\ **Note** Available as of programme version 2.8.0 | User interface > Main window > Toolbar > [[en:infra-convert:user:interface:toolbar#en:infra-convert:user:interface:toolbar#the_viewing_tools_group|The “Viewing tools” group]] |
^ <del>CommonAppDataPath</del> | Path to the general program data directory %ProgramData%\\ \\ **Attention** Never completely worked. Passed as of program version 1.3.7.0 as start parameter [[en:infra-convert:dev:parameter|forceConfigDir]]. |  |
^ PdfExportTextAsGeometry | Export text as geometry to PDF\\ \\ **Note** Available as of programme version 2.7.13 | Functions > Export > Export drawing > [[en:infra-convert:user:functions:pdfexport#workflow|Workflow]] > PDF |

\\ 

<WRAP group>
<WRAP column 3%>
{{:en:infra-convert:icon_hinweis_stop.png?nolink&25}}
</WRAP>
<WRAP column 92%>
**In-program parameters**
</WRAP>
</WRAP>

|< 100% 20% 40% 40% >|
^  Name  ^  Value  ^  Link  ^
^ MacrosAfterLoad |  |  |
^ MacrosAfterOpen |  |  |
^ RecentFiles | Links to recently opened projects listed in the start window | User manual > Main window > [[en:infra-convert:user:interface:startwindow|Start window]] |
^ RecentDocumentPath | Link to the directory from which files were last opened |  |
^ RecentExportPath | Link to the directory to which the most recent export was made |  |
^ CharacteristicTextFormatting |  |  |
^ StampStartValue |  |  |

\\ 

==== Installation/Deinstallation ====

The following describes the process for deinstalling, reinstalling (installing after previous deinstallation) and installing (without previous deinstallation) #@IC_HTML@# using the parameter file “settings.json”. Essential preconditions are: the file is at the location where it was installed, and has not been renamed.

> **See also** Introduction > Overview (program version 2) > [[en:infra-convert:dev:intro_preview#installation_uninstallation|Installation/Uninstallation]]

<WRAP group>
<WRAP column 25%>

**Deinstallation**

</WRAP>

<WRAP column 65%>

The file is neither deleted or changed.

</WRAP>
</WRAP>

<WRAP group>
<WRAP column 25%>

**Reinstallation**

</WRAP>

<WRAP column 65%>

An existing file is not changed.

</WRAP>
</WRAP>

<WRAP group>
<WRAP column 25%>

**Installation**

</WRAP>

<WRAP column 65%>

An existing file is not changed.

</WRAP>
</WRAP>

<WRAP noprint>

----

<WRAP group>
<WRAP col2>

<WRAP rightalign>

**Scroll backwards**\\ 
Configuration and Import > [[en:infra-convert:dev:parameter|Startup parameter file]]

</WRAP>

**Scroll forwards**\\ 
Configuration and Import > [[en:infra-convert:dev:characteristictags|"CharacteristicTags” parameter file]]

</WRAP> </WRAP>

</WRAP>
ELIAS GmbHProduktdokumentationen

User Tools

Site Tools

Page Tools

ELIAS GmbH
Produktdokumentationen
