Differences

This shows you the differences between two versions of the page.

--- en:infra-convert:user:config:tolerancetables [2017/07/06 09:25]
me created
+++ en:infra-convert:user:config:tolerancetables [2022/06/10 16:23] (current)
me
@@ Line 1: / Line 1: @@
 ~~NOTOC~~
-{{ :en:icon_uebersetzung_in_arbeit.png?nolink&150 |}}
+<WRAP noprint>
+> User manual #@IC_HTML@# > Settings > Project settings
+</WRAP>
+====== Tolerance tables ======
+----
+The general tolerance tables valid for the project can be selected on the //Tolerance tables// tab of the //Project settings// menu. Click on
+  * **Apply,** at the bottom of the window to save the changes without closing the window,
+  * on **OK,** to save the changes and close the window or
+  * on **Cancel,** to discard the changes.
+The settings are saved with the project.
+> **Note** Your CAQ system provider or administrator may be able to prevent you from changing some settings under certain circumstances. Please contact them if an incorrectly set option interrupts your workflow.
+The default values of the settings can be specified in the parameter file "Settings", see Administrator Manual #@IC_HTML@# > Configuration and Import > [[en:infra-convert:dev:settings|Parameter File "Settings"]].
+\\
+<WRAP noprint>
+<WRAP group>
+<WRAP column 35%>
+//**__Content__**//
+ • [[en:infra-convert:user:config:tolerancetables#Invoke]]\\
+ • [[en:infra-convert:user:config:tolerancetables#“Length measurements” group]]\\
+ • [[en:infra-convert:user:config:tolerancetables#“Angular measurements” group]]\\
+ • [[en:infra-convert:user:config:tolerancetables#“Radius of curvature and chamfers” group]]\\
+ • [[en:infra-convert:user:config:tolerancetables#Save/Export]]
+\\
+</WRAP>
+</WRAP> </WRAP>
+==== Invoke ====
+The menu can be invoked as follows:
+<WRAP group>
+<WRAP column 20%>
+**Menu bar**
+</WRAP>
+<WRAP column 75%>
+Click on **Edit** and then on **Project settings** in the drop-down menu that opens. The //Project settings// menu window opens. Select the **Tolerance tables** tab in the list on the left side of the window.
+</WRAP>
+</WRAP>
+\\
+==== “Length measurements” group ====
+{{page>en:infra-convert:user:config:tolerancetables:linear_en}}
+\\
+==== “Angular measurements” group ====
+{{page>en:infra-convert:user:config:tolerancetables:angle_en}}
+\\
+==== “Radius of curvature and chamfers” group ====
+{{page>en:infra-convert:user:config:tolerancetables:edge_en}}
+\\
+==== Save/Export ====
+{{page>en:infra-convert:user:config:save_project_settings}}
+{{page>en:infra-convert:user:config:backup_project_settings}}
+<WRAP noprint>
+----
+<WRAP group>
+<WRAP col2>
+<WRAP rightalign>
+**Go to previous page**\\
+Settings > Settings > [[en:infra-convert:user:config:administration|Administration]]
+</WRAP>
+**Go to next page**\\
+Settings > Project settings > [[en:infra-convert:user:config:label|Tags]]
+</WRAP> </WRAP>
+</WRAP>

ELIAS GmbHProduktdokumentationen

User Tools

Site Tools

Differences

Page Tools

ELIAS GmbH
Produktdokumentationen