ELIAS GmbH
Produktdokumentationen

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
===== Mahr i-Stick =====

The additional module for **Mahr Integrated Wireless** measurement devices is not included in the basic version of MDM-Tool.

==== Connecting a Mahr Integrated Wireless measurement device ====

The following describes how to connect a Mahr Integrated Wireless measurement device to your PC.

{{:en:mdm:inputdevices:istick_a1_eng.png?500|}}

Double click the **+ Add new device** entry field in the **Mahr i-Stick** list to open the devices list. All measurement devices that are recognized are listed here.

{{:en:mdm:inputdevices:istick_a2_eng.png?500|}}

Now open the measurement device's configuration menu (the device's menu, not the MDM's) and switch to ID configuration. Reset the device's ID. If the ID is properly reseted, the device's display shows "- - - - -". Now push the button for transmitting a measurement value. After a few seconds the measurement device should appear in the MDM-Tool's device list.

Select the measurement device you want to connect and click the **Add** button. The measurement device is now listed in the **Input devices** list and is automatically connected to the standard output device, the **Virtual Keyboard**. 

{{:en:mdm:inputdevices:istick_a3_eng.png?500|}}

Pressing the button on the measurement device transmits measurement data from the device to keyboard interface. Transmitted measurement values are then displayed in the lower part of the window. As a check, compare these values with those displayed on your handheld measuring device.
\\
\\
The green icon next to the device shows you that the device is turned on. If the device is turned off, the icon turns yellow. As additional information is displayed the battery level of the transmitter.
\\ 
\\
<WRAP pagebreak></WRAP>
==== Configuring a Mahr Integrated Wirless measurement device ====

This section describes how to configure a Mahr Integrated Wirless measurement device.

Mouse click to select the device you want to configure from the list.

{{:en:mdm:inputdevices:istick_b1_eng.png?500|}}

Click the **Configure** button below the list. You can also right-click to open the context menu and select **Configure** from the menu list.

{{:en:mdm:inputdevices:istick_b2_eng.png?500|}}
{{:en:mdm:inputdevices:istick_b3_eng.png?500|}}

You can activate or deactivate the measurement device by clicking the **Enabled** check box.  

You can enter a name for the device in the **Name** field. This is then displayed in the list. This makes identification easier if there are more than one device in the list. 

The serial number and type of the measurement device are also displayed. These settings cannot be changed. 

{{:en:mdm:inputdevices:istick_b4_eng.png?500|}}

In the **Feedback** menu select the output device from which you expect acknowledgement of receipt for measurement data. If you select the **green LED** from the list, this LED on the transmitter will light up when measurement value has been processed. Selecting **Virtual COM Port** or **Virtual Keyboard** from the list results in this device taking on the acknowledgement of receipt and the corresponding LEDs light up. 

Click **Delete** to remove the measurement device from the list.

Click **Apply** to adopt the settings you have chosen. Clicking **OK** saves the data and closes the Settings window. Clicking **Cancel** closes the window without saving any changes. 

<WRAP pagebreak></WRAP>
==== Configuring a Mahr i-Stick USB dongle ====

This section describes how to configure a Mahr i-Stick USB dongle. 

{{:en:mdm:inputdevices:istick_c1_eng.png?500|}}

Select the USB dongle you want to configure from the list.

{{:en:mdm:inputdevices:istick_c2_eng.png?500|}}

Click the **Configure** button below the list to open the configuration window. Alternatively, you can also right mouse click to open the context menu and select **Configure** from the menu list.

{{:en:mdm:inputdevices:istick_c3_eng.png?500|}}
 
You can click the **Enabled** check boxes to deactivate or activate the USB dongle. 

The name of the COM port connected to the USB dongle is also displayed. This setting cannot be changed. 

Click the **Close** or **Configure** buttons to close the window.

<WRAP pagebreak></WRAP>
ELIAS GmbHProduktdokumentationen

User Tools

Site Tools

Page Tools

ELIAS GmbH
Produktdokumentationen
