infra CONVERT
blue DAT • infra DAT
mdm TOOL
Sidebar
en:wmdt:user_bd:transm
Content
The blue DAT system transmitter can be connected to any of the usual digital measuring devices. As different measuring device manufacturers use different connectors, each transmitter is shipped with the appropriate connector for your device(s).
The compact size of the new blue DAT system makes it possible for use at mobile measurement sites, e. g. direct connection to tablets, notebooks etc. Compared to the infra DAT system, the new blue DAT system has significantly longer battery life and higher transmission rates.
Since every transmitter has a unique ID number, measuring equipment can easily be monitored and the transmitted data tracked. LEDs on the transmitter tell the user when data is transmitted.
It is possible to connect any number of digital devices to a measurement site. The transmission-secure Bluetooth® Smart standard means that any number of measurement stations can be operated simultaneously with the Measurement Data Management software mdm - TOOL making it possible to quickly and easily assign data to its source measurement station.
Depending on application and local conditions data can be radio transmitted up to a range of 10 m.
To transmit data to a PC you need a blue DAT receiver and our Measurement Data Manager software shipped with the receiver. You can also download this software from the following link on our website:
https://www.elias-gmbh.de/en/service/downloads#mdm
Read the contents of this very carefully. Failure to follow its instructions may invalidate guarantees!
Intended use
This device may only be used as authorized and compliant with all the information published about its use. Any use or application other than that expressly authorized is deemed inappropriate. The manufacturer accepts no liability for any damage arising from such misuse. Comply with and observe all laws and regulations applicable for use of the device.
Installing the batteries
To insert the batteries, open the battery compartment. Insert the batteries making sure polarity is correctly aligned. Replace the battery compartment lid.
Technical data
| Radio transmission frequency | 2.4 GHz |
|---|---|
| Technology | Bluetooth® Smart |
| Qualified Design ID (BlueGiga BLE112) | B018943 |
| Battery | 1 x CR 1/3N (3 V) |
| Operational temperature range | +10 °C … +35 °C |
| Relative humidity | 30 % … 90 % |
| Appliance class (depending on local conditions) | IP40 |
| Transmission range (depending on local conditions) | approx. 10 m |
| Dimensions L x B x H | 52 mm x 26 mm x 16 mm |
This device contains FCC ID: QOQBLE112 / IC ID:5123A-BGTBLE112
Declaration of Conformity:
This product complies with Directive 2014/53/EU (RED) and
2011/65/EU, 2015/863/EU (RoHS). The relevant Declaration of Conformity
can be requested at info@elias-gmbh.de.
FCC compliance & advisory statement
Note This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
en/wmdt/user_bd/transm.txt · Last modified: 2024/03/21 11:13 by me
